The Importance of Proper Spark Plug Torqueing
Why Alternators Are Subject To Ripple Voltage
PRT & PRT HEAVY DUTY To Exhibit at “The Group” Annual Member Expo
The Importance of Proper Spark Plug Torqueing
Why Alternators Are Subject To Ripple Voltage
PRT & PRT HEAVY DUTY To Exhibit at “The Group” Annual Member Expo
Sponsored By NGK Spark Plugs
Do the letters “GDI” scare you? If gasoline direct injection or GDI has you avoiding diagnostics and repairs on late-model vehicles, we have some training for you! In this 45-minute webinar, experts will help you understand GDI systems from the strainer in the tank to the nozzles in the combustion chamber.
At the end of the webinar, you will have a better understanding of how a GDI fuel system operates, so you have a solid diagnostic foundation.
Speakers Jeff Boehler, Director of Engineering/Chief Engineer, Autolite Andrew Markel, Director of Content, ShopOwner
Underhood Service targets repair shops that derive 50 percent or more of their revenue from the service and repair of under-the-hood systems. The expanding amount of knowledge and capital needed to keep up with technological advances has led these shop owners to concentrate on underhood systems, while also offering preventive maintenance services on most major vehicle systems. By subscribing, you’ll receive the ShopOwner digital edition magazine (12 times/year) featuring articles from Underhood Service and the Underhood Service eNewsletter (twice weekly). Access to digital editions, contests, news, and more are ready for you today!
Underhood Service targets repair shops that derive 50 percent or more of their revenue from the service and repair of under-the-hood systems. The expanding amount of knowledge and capital needed to keep up with technological advances has led these shop owners to concentrate on underhood systems, while also offering preventive maintenance services on most major vehicle systems. By subscribing, you’ll receive the ShopOwner digital edition magazine (12 times/year) featuring articles from Underhood Service and the Underhood Service eNewsletter (twice weekly). Access to digital editions, contests, news, and more are ready for you today!
High underhood temps, increased power demands and vibration can damage alternators or starters. Sponsored by ACDelco.
Don’t settle for “almost” - it matters where the engine is manufactured or remanufactured. Sponsored by ACDelco.
Brake pads are thoroughly developed to produce the best result. This video is sponsored by ZF Aftermarket.
Click here to view past issues.
Get the latest news, insights, and more delivered directly to you inbox.
Hydraulic lifters are precision-fit assemblies.
The basic function of a valve lifter is pretty simple. It sits on the camshaft and transfers the motions of the cam lobe up through the pushrods and rockers to open and close the valves. The size and shape of the cam lobe under the lifter (multiplied by the ratio of the rocker arms) determines valve lift and duration. As such, the lifter just follows the motions of the cam. But it does play a role in valvetrain lash (clearance) and noise.
The area of contact between the lifters and cam lobes is the highest loaded surface inside an engine, with as much as 200,000 to 300,000 psi at the point of contact depending on valve spring pressure! Consequently, it is critical that both components have the correct geometry (both convex and taper), that both surfaces have adequate hardness to resist premature wear and failure, and that the point of contact receives good lubrication with the motor oil.
A big improvement came about with the invention of roller lifters. By placing a small wheel on the bottom of the lifter, friction between the cam and lifter is greatly reduced. That’s why all modern pushrod engines have roller lifters. Roller lifters also allow the use of more radical cam lobe profiles with faster opening and closing ramps that provide more total valve opening for a given lift and duration.
Mounting a wheel on the bottom of the lifter also changes the dynamics between the lifter and cam. A roller lifter has to be held in fixed alignment with the cam so the wheel will roll smoothly on the lobe, so you don’t want the lifter to rotate or twist.
If the original cam and lifters are still in good condition and are being reused, make sure all of the lifters are reinstalled in their original holes (same location as before). However, if the original cam is worn and needs to be replaced, replace the lifters, too. Don’t ruin the new or reground cam by reusing worn lifters.
The only exception to this rule is with roller cams. Because the cam lobes are flat and the lifters have rollers rather than a convex surface, a new roller cam can be installed with used roller lifters, provided all of the lifters are in good condition with no damage, pitting or cracking.
Hydraulic lifters were first developed back in the 1930s and became common in production engines in the 1950s. Hydraulic lifters eliminate the clatter produced by solid lifters because the valvetrain runs with zero lash (clearance). Solid lifters require a small air gap between the tips of the rocker arms and the tops of the valve stems to compensate for thermal expansion in the engine as it heats up.
Lash adjustment is critical because too much clearance makes the valves noisy and reduces valve lift, duration and performance. Too little clearance can also create problems because it causes the valves to open sooner and close later, reducing heat dissipation through the valve seats when the valves are closed. This can make some valves (especially exhaust valves) run too hot and fail.
If the lash is way too tight and closes up entirely, it may hold the valve open causing a loss of compression and possibly contact between the valve and piston.
Hydraulic lifters eliminate the clatter and the need for periodic adjustments by maintaining zero clearance when the engine is running. They do this by using oil pressure against a spring-loaded plunger inside the lifter body. Oil fills the cavity under the plunger when the valve is closed. This pushes the plunger up to take the slack out of the valvetrain and hold it tight.
A one-way check valve inside the lifter holds the pressure inside the lifter as the valve opens. Since oil is incompressible, the oil trapped under the plunger prevents the plunger from compressing and the lifter acts like a solid lifter to push the valve open.
Hydraulic lifters are also kinder on valvetrain components than solid lifters because zero valve lash reduces the hammering effect that occurs when the valves slam shut at higher engine speeds. There’s no air gap to fill so the valve simply follows the cam lobe as it closes for a more gentle landing. This also reduces noise and helps extend the life of the valvetrain components.
At high speed, hydraulic lifters may “pump up” and hold the valves open causing the valves to float. This can occur if the valve springs are not strong enough to maintain normal valve control, and the lifters try to take up the slack that really isn’t there. This overextends the plunger and prevents the valve from closing all the way. The same thing can happen if the oil inside the lifter does not bleed down quickly enough between cycles to maintain normal valve lash.
Hydraulic lifters are precision-fit assemblies. The plunger is closely matched to the housing to provide minimal clearance so the leakdown rate is not too great or too small. That’s why you should never intermix the internal parts when you are cleaning and rebuilding a set of hydraulic lifters. Clean each lifter individually so the original assembly tolerances are maintained.
The ongoing quest to squeeze more fuel efficiency out of today’s engines has lead to the development of various “displacement on demand,” “variable displacement” or “cylinder deactivation” technologies on some engines. Basically, the idea is to deactivate up to half of the engine’s cylinders when it is under light load to conserve fuel. Switching off the fuel injectors to kill certain cylinders saves fuel. But if the valves are still opening and closing, the engine is wasting energy pumping air through the dead cylinders. The valves also have to be deactivated at the same time to maximize the energy savings.
Deactivating the valves traps air in the dead cylinders. This creates an “air spring” effect that returns almost as much energy on the piston downstroke as is put in during the compression upstroke. The engine squeezes the air during the compression stroke, and the air pushes back as it expands during the downstroke.
There are various ways to deactivate cylinders, including cams that have different lobes for each cylinder, changing the position of the rockers or using hydraulic lifters that can collapse on command to eliminate valve lift. A variable-position valve lifter can operate with normal plunger height or reduced plunger height. This requires a secondary oil supply hole and valving to change the position of the plunger inside the lifter.
The powertrain control module (PCM) regulates the oil pressure to the lifters via solenoid valves. With multiple-cylinder deactivation, several solenoids may be used to control oil flow to various lifter pairs. Problems with engine sensors (notably MAP, airflow and throttle position sensors), the oil flow control solenoids, engine oil pressure (if the engine is also equipped with a variable displacement oil pump), the PCM or wiring faults may all affect the normal operation of such a system.
Hydraulic lifters will normally make some noise when an engine is initially fired up, but should soon quiet down as oil fill the lifters and the lifters expand to tighten up the slop in the valvetrain. Some experts say hydraulic lifters should be presoaked in oil and bled prior to installing them. Others say this isn’t necessary and actually increases the risk of the lifters holding the valves open too far.
The normal procedure for adjusting a set of hydraulic lifters is to rotate the cam so each pair of lifters is at their lowest position on the base circle of the cam. This is done by rotating the crank so that the cylinder is at Top Dead Center on its compression stroke with both valves fully closed. The rockers are then adjusted to zero lash and then given an additional 1/2 to 3/4 turn to push the plungers inside the lifters down to their midrange position. The procedure is then repeated for each cylinder until all the lifters have been preset. If the lifters are prefilled with oil, they may not push down when the rockers are given the additional twist, causing the valves to lift off their seats instead.
Engine: Serpentine Belt Post Mortem: Why Do Some Belts Fail
Electronic: Understanding Stop/Start Charging and Starting Systems
Engine: GM Active Fuel Management System Service
Engine: What Caused The Turbo To fail?